INTRODUCTION &
DESCRIPTION
The digital blood analyzer is designed
to make the analysis simple. The cumbersome
step of calculations is deleted. The final
result of unknown test will be displayed
directly in concentration. There is no
need of any calculations. However optical
density (O.D.) switch is also given in
case of optical density is required to
cross check the reading at any time. A
micro controller has been incorporated
in the system for accuracy precision and
reproducibility of findings.
Best quality eight numbers of optical
built in glass filters are included in
the equipment to cover complete visible
range of wavelength from 400 nm to 700
nm. The wavelength can be set by rotation
of the filter wheel. The system works
with square cuvette and only 1 ml reagent
to be used. This analyzer, also operate
on 12 V battery. The very important feature
of this system is that the instrument
can be run in two different modes i.e.
STD or NON STD modes.
STD Mode : In STD mode, the user has to
put standard solution, i.e. known CONC.
of STD has to be fed every time for testing.
NON STD Mode :
The need of using standard solution daily
is simply overcome by feeding the O.D.
of the STD solution by using BLANK only.
TECHNICAL SPECIFICATION
Optical
System : Special optical glass filters (8
nos.)
Wavelength of filters : 400, 490, 520, 540,
590, 620, 650, 700 nm
Display : RED color LED 3 digits, 7 segments
Indicators : RED color LED
Light source : 6 V, 315 mA Tungsten lamp
Detector : Highly Sensitive Se photocell
Reagent Volume : Minimum 1 ml
Cuvette : Square cuvette (10 mm optical
path)
Key pad : 4 x 4 very soft feather switch
key board
Reading display : Direct reading in CONC.
(ABS & TRANS also available)
Operating Models : i STD Mode
ii NON STD Mode
Decimal Position Display : i 0.00
ii 00.0
Input Voltage Mains : 230 V, + 10% AC, 50
Hz
Battery : 12 V
Weight : Approx. 5.0 Kg
Dimension : 13 x 11.5 x 8”
| Optional System |
: Glass Filters (8 Nos.) |
| Wave Length |
: 400 – 700 nm |
| Peak Wave Lengths |
: 400, 490, 520, 540, 590, 620, 650,
700 nm (On wheel) |
| Auto Zero Facility |
: In all filters (i.e. 400 –
700 nm) |
| Display |
: LCD Alpha Numeric (16 x 1) |
| Detector |
: Highly Sesitive Photodiode Reagent
Volume : Minimum 1 ml |
| Reagent Volume |
: Minimum 1 ml |
| Cuvette |
: Square Cuvette 10 x 10 (Plastic) |
Kay Pad
|
: 3 x 2 Feather Switch Key Board |
| Light Source |
: 6 V, 10 W, Tungsten Lamp |
| Feeded Tests |
: Values of STD Conc./ Factors of
SUGAR,
UREA, CHOLESTROL, TOTAL PROTEIN, ALBUMIN,
URIC ACID, HAMEOGLOBIN, CHLORIDE, CALCIUM,
TRIGLY CERIDES, BUN, HDL CHOLESTROL
CREATINE, ALKALINE PHOSPHATE, SODIUM,
ACID PHOSPHATE BILIRUBIN, POTASSIUM
S.G.O.T, SGPT (DNPH Method) are already
fed. |
| Operating Modes |
: CALIBRATION / MEASUREMENT / PHOTOCOL |
| Readings |
: DIRECT READING IN CONC./O.D. |
| Cooling System |
: A fan inbuilt for Cooling |
| Dimensions |
: 325 x 260 x 120 nm |
| Weight |
: 4.5 kg (Approx.) |
| Input Voltage |
: AC Mains : 230 V, 50 Hz, 1 F AC. |
| Battery |
: 12 V |
|
| STEPS OF OPERATION
MODE STD.,
O.D./CONC.K6 O.D.SAMPLEK5 SCAN (+)DEC. +K4
SCAN/STOPK1 ENTERK2 SCAN (-)DEC. –K3
i. • Switch
ON the instrument (Given on Right hand of
the machine)
- Display will show ‘K – Blood
Analyzer’.
- Scanning starts, SUGAR, UREA, ……..
PHOTO COL.
ii. • To stop PRESS K1 at desired
TEST.
• It can restart by pressing K1 again.
• It can advance/retreat in steps
i.e. one by one by pressing K4 and K3, resp.
iii. • PRESS K2 ENTER
- Display will show MEASUREMENT
iv. • Select MEASUREMENT/CALIBRATION
by K1.
v. • PRESS K2 ENTER
|
Copyright © Medical Surgical Equipments. All Rights Reserved